Coolant Flush How To Jeep Grand Cherokee 1993 1998 1998 This video shows where the radiator drain plug (petcock) is located on a 1998 jeep grand cherokee. fill up the radiator with distilled water and run the engine. turn off the engine and drain the water, fill up the radiator with antifreeze until you have a 50 50 coolant distilled water mixture and burp the system. Pour in the coolant system flush. start engine and let the jeep run for 15 minutes with the heater on highest temperature and fans on full blast. step 2. once the running is done, get beneath the front end of your jeep. locate the drain plug of your radiator. it's on the driver side of the radiator.
Flushing Coolant From The Jeep Grand Cherokee Radiator In today’s video i show you guys a quick and easy way to flush your radiator and your engine block for free at home and to do it in under an hour or so to ma. As for draining and flushing, look for a drain plug. some vehicles have it on the engine and or the radiator. once drained, you can add water (personally, i buy a few gallon jugs of distilled water) and drain it couple of times. then, using the tool, i fill the coolant to avoid any air pockets. hope this helps. Park your jeep grand cherokee and turn off the engine. 2. lift the hood and locate the radiator cap. 3. place a large drain pan beneath the radiator drain valve and open the valve to drain the coolant. 4. once the coolant has finished draining, close the valve and remove the drain pan. 5. Buy a cheap socket that is smaller than the length of the tab on the end of the drain knob for the petcock. cut two slots in the socket to allow the tab on the petcock to fit down into those slots. then use this socket to turn the petcock. it's got a fast acme thread on it, so only about 1 2 turn is fully open.
How To Flush An Engine Radiator How A Car Works Park your jeep grand cherokee and turn off the engine. 2. lift the hood and locate the radiator cap. 3. place a large drain pan beneath the radiator drain valve and open the valve to drain the coolant. 4. once the coolant has finished draining, close the valve and remove the drain pan. 5. Buy a cheap socket that is smaller than the length of the tab on the end of the drain knob for the petcock. cut two slots in the socket to allow the tab on the petcock to fit down into those slots. then use this socket to turn the petcock. it's got a fast acme thread on it, so only about 1 2 turn is fully open. Remove the lower radiator hose and thermostat when thats done you can flush out the old coolant from the block. jeep cherokee xj 4.0 89. jeep cherokee xj 4.0 90 (partsjeep) jeep grand cherokee 5.2 93. chevrolet silverado 2500 6.5td 94. chevrolet c20 6.2 82. Step 2 – flush radiator. after you've let all the coolant drain from the radiator and into the container, tighten the drain plug. fill the radiator with distilled water, close the radiator's cap, and let the car run for a few minutes with the heater on. this will allow the thermostat to open. flush the radiator again by opening up the cap and.
Flushing Coolant From The Jeep Grand Cherokee Radiator Remove the lower radiator hose and thermostat when thats done you can flush out the old coolant from the block. jeep cherokee xj 4.0 89. jeep cherokee xj 4.0 90 (partsjeep) jeep grand cherokee 5.2 93. chevrolet silverado 2500 6.5td 94. chevrolet c20 6.2 82. Step 2 – flush radiator. after you've let all the coolant drain from the radiator and into the container, tighten the drain plug. fill the radiator with distilled water, close the radiator's cap, and let the car run for a few minutes with the heater on. this will allow the thermostat to open. flush the radiator again by opening up the cap and.
Comments are closed.